Installing NEOSYS

INSTALLING NEOSYS SERVICE

Main installation:

Downloading and running installation files

1. http://www.neosys.com/support/accounts.exe ... and install to X:\Neosys
2. http://www.neosys.com/support/adagency.exe ... and install to X:\Neosys

Creating shortcuts

Make desktop shortcut ‘Maintenance’ from X:\Neosys\Neosys\Adagency.bat

Activating NEOSYS using authorization number

Start NEOSYS Maintenance and it will give a “Computer Number” and ask for an “Authorisation No”

Send the computer number to NEOSYS admin to get the authorization no.

If you cannot get the authorization number immediately then you can close NEOSYS and when you reopen NEOSYS it will still give the same computer number and accept the same authorization number.

Installing initial Database

First time entering maintenance you will enter a command box (like NEOSYS F5)

Type FILEMAN and then restore. You will need a BACKUP.ZIP file in C:\ containing the initial database.

Creating a .CMD file to start NEOSYS Service:

In x:\neosys create a file startmain.cmd

x:
cd \neosys\neosys
Start neosys.js /system ADAGENCY /database databasecode /user NETSERVICE /pass NETSERVICE

(where databasecode is the code of the database)

In x:\neosys create a file starttest.cmd

x:
cd \neosys\neosys
Start neosys.js /system ADAGENCY /database testdatabasecode /user NETSERVICE /pass NETSERVICE

(where testdatabasecode is the code of the testdatabase)

Differences for Pure Accounts Module Only Installations

Accounts module only has a slightly different startup command. In the above, replace /system adagency with /system accounts to startup a service and use accounts.bat instead of adagency.bat to start up maintenance. Other than that, accounts module setup is identical. Pure accounts clients are very few and tend not to upgrade often so care needs to be taken when upgrading. Upgrade is perhaps surprisingly done using the adagency.exe file.

Creating a .CMD file to copy maindata to testdata

In x:\neosys create a file copymain2test.cmd

Xcopy x:\neosys\data\maindatabasecode x:\neosys\data\testdatabasecode /s /y

Setting up daily scheduled tasks

Maindata – 3 processes starting 6:00 am, 6:01 am, 6:02 am

Testdata – 1 process at 6:04 am

Copy Maindata to Testdata – 1 process at 2:45 am

For multiple sites on the same computer put the second site starting five minutes later at 6:05, third site starting five minutes earlier at 5:55, the third site starting five minutes later at 6:10 and so on.

Measuring the speed of NEOSYS

In NEOSYS maintenance mode press F5:

FILESPEED

Measures the speed at to create and delete a file with 1000x1Kb records - lower time is better

Example speed is 1 second on a high quality notebook 7200rpm Hitachi deskstar Speeds less than 8 seconds are acceptable for small installations Speeds less than 4 seconds are acceptable for larger installations Antivirus usually needs to be configured to exclude OV or OV? files. See section Configuring Antivirus for NEOSYS

PROCSPEED

Measures the processor speed – higher speed is better

Example speed is 550,000 tests per second on an Intel Core Duo 1.8Ghz

MEMSPEED

Measures the memory speed – higher speed is better

Example speed is 50,000 tests per second on an Intel Core Duo 1.8Ghz with 667MHz DDR 2 SDRAM

CLOSING NEOSYS SERVICES

Two automatic ways:

• NEOSYS services will automatically initiate a database integrity check, “backup” and close down at 2am by default.

To change the time of the automatic process do F5 ED DEFINITIONS

line 3 is the minimum time to start the backup and shutdown (default 7500 ie 02:00) line 4 is the maximum time to start the backup and shutdown (default 7800 ie 02:05)

both times must be in seconds past midnight

press F5 and type PRINT ICONV(’02:00’,’MTH’) to calculate this easily

• NEOSYS will automatically close down during the upgrade procedure.

Three manual ways:

Warning: NEOSYS services do not shutdown automatically on server shutdown so you need to use one of these methods before shutting down or rebooting a server.

• To close individual services, press Esc three times on a service and then ctrl+C once or twice. Repeat for each service that you want to close.

This can only be done if you can actually see the services on the screen but the services will not be visible if they were started by scheduled tasks while administrator was not logged in to the server … unless you login as /console with remote desktop.

• To close all services for one site/neosys installation, use the NEOSYS Support Menu – Stop/Restart NEOSYS

Currently this has no option to stop the services for any other neosys sites/installations on the same server

• To close all services for all sites and installations of NEOSYS under a particular folder, use NEOSYS maintenance (or any other program) to create and then delete a GLOBAL.END file in the parent folder of all the neosys installations. eg if the installations are located in x:\hosts\clientcode\neosys etc then create and delete a file called x:\hosts\GLOBAL.END

1. In NEOSYS Maintenance press F5 to get a NEOSYS command prompt

1. Type ED DOS ..\..\GLOBAL.END and press Enter

(use ED DOS GLOBAL.END instead if you only want to close the services of the current site)

1. Press F9 to create the GLOBAL.END file

1. Wait until the processes close. Should be almost immediate.

1. Press alt+D twice to delete the GLOBAL.END file otherwise Neosys services will refuse to start